• Hammers
  • Abrasive
  • Knives
  • Orthopedic tools
  • Scissors
  • Scewdrivers
  • Pliers
  • Wrenches
  • Files, Rasps
  • Saws
  • Drill bit
  • Measuring tools
Centre punch, standard quality DIN 7250 100 mm
Strong octagonal shank, bright finished point. Uniformly through hardened over the entire length. Head specially annealed to prevent splintering.
Safety tested to DIN 7255.
Material: Chrome vanadium air hardening steel, painted. Head annealed.
overall length: 120 mm
Shank ⌀: 10 mm
Type of striking head: annealed
Material: Chrome vanadium air hardening steel
Surface: painted
Register to see prices 0.0 USD
Flexible steel rule narrow, stainless matt finished 150mm
Of stainless spring steel strip.
Clean electrolytically applied black graduations and figures with a smooth surface. Easy to read. Rounded edges to prevent injuries.
Upper and lower edges both with 1 mm graduations.
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Straight scriber
1 straight point; knurled metal handle.
overall length: 180 mm
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Permanent marker, black
edding 400, round point, line thickness approx. 1 mm.
Application:
For marking on almost all materials, even metal, glass, plastic.
Manufacturer's designation: edding 400
maximum line thickness: 1 mm
Writing colour: black
quick-drying: yes
waterproof: yes
refillable: yes
Register to see prices 0.0 USD
Flexible steel rule narrow, stainless matt finished 200mm
Of stainless spring steel strip.
Clean electrolytically applied black graduations and figures with a smooth surface. Easy to read. Rounded edges to prevent injuries.
Upper and lower edges both with 1 mm graduations.
Register to see prices 0.0 USD
Angle scriber
1 straight and 1 angled point; nylon handle. Point hardness 48 - 55 HRC.
overall length: 230 mm
Type of product: Steel scriber
Register to see prices 0.0 USD
Locking tape measure 2 m
Boîtier en plastique avec clip-ceinture amovible. Rembobinage automatique amorti et blocage du ruban. Crochet terminal mobile, CRM 391
Register to see prices 0.0 USD
Tape Measure, Tailor, Flexible, 1.5m
Tape measure of light quality, for everyday use. Yellow/white ribbon in polyfiber fabric with black graduation on both sides. Metal tip at both ends.
Length: 150cm
Width: 18.5mm
Register to see prices 0.0 USD
Flexible steel rule narrow, stainless matt finished 300mm
Of stainless spring steel strip.
Clean electrolytically applied black graduations and figures with a smooth surface. Easy to read. Rounded edges to prevent injuries.
Upper and lower edges both with 1 mm graduations.
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Flexible steel rule narrow, stainless matt finished 1000mm
Of stainless spring steel strip.
Clean electrolytically applied black graduations and figures with a smooth surface. Easy to read. Rounded edges to prevent injuries.
Upper and lower edges both with 1 mm graduations.
Register to see prices 0.0 USD
Flexible steel rule narrow, stainless matt finished 500mm
Of stainless spring steel strip.
Clean electrolytically applied black graduations and figures with a smooth surface. Easy to read. Rounded edges to prevent injuries.
Upper and lower edges both with 1 mm graduations.
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Locking tape measure with automatic tape lock 2m
Automatic blocking of the ribbon during stretching.
Rewinding the ribbon by pressing the button.
Mobile terminal hook.
Yellow tape measure, printed black / red, acrylic coating for better resistance to abrasion.
Case dimensions: 52x49x22mm
Ribbon length: 2m
Band width: 13mm
Register to see prices 0.0 USD
Plumb line
With clearance plate, line : 4 m, D 2mm
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Engineer’s precision steel rule stainless, matt finished 300 mm
Of special stainless clock spring steel with ground measuring edges. Wide version. Upper and lower edges both with mm graduations. Very easy to read due to matt surface and sharp graduation scale.
Graduations electrolytically etched. Matt non-reflective surface.
Register to see prices 0.0 USD
Spring dividers with points 220mm
Sturdy design with long arms, made of tool steel. Points and measuring faces ground and hardened. Solid spindle with adjusting nut for quick and fine adjustment. Annular spring provides constant spring tension.
With replaceable tips.
Register to see prices 0.0 USD
Dividers, 150mm
Sturdy design with chamfered arms, tool steel, forged and precision ground. Riveted through joint hinge. Hardened and ground points.
Register to see prices 0.0 USD
Spring dividers with points 170 mm
Sturdy design with long arms, made of tool steel. Points and measuring faces ground and hardened. Solid spindle with adjusting nut for quick and fine adjustment. Annular spring provides constant spring tension.
With replaceable tips.
Register to see prices 0.0 USD
Square 90° 150X100mm
All faces and edges ground. Inspection test faces ground.
Application:
For accurate general workshop work.
Accuracy:
DIN 875 / 2 − angle tolerance e.g. for size 100×70 = 0.030mm.
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Dividers with quadrant 150 mm
Sturdy design with chamfered arms, tool steel, forged and precision ground. Riveted through joint hinge. Hardened and ground points.
Register to see prices 0.0 USD
Engineer’s precision steel rule stainless, matt finished 500 mm
Of special stainless clock spring steel with ground measuring edges. Wide version. Upper and lower edges both with mm graduations. Very easy to read due to matt surface and sharp graduation scale.
Graduations electrolytically etched. Matt non-reflective surface.
Register to see prices 0.0 USD
Automatic center punch with point, 110 mm
Robust, knurled body with interchangeable hardened tip and ergonomic tip for high user comfort. The punching power can be adjusted at will by rotating the tip.
Material (s): Special tool steel.
Total length: 110 mm
⌀ tail: 10 mm
Min impact force: 47 N
Max impact force: 78 N
Material: Special tool steel

Register to see prices 0.0 USD
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Combination Square 300mm
Sliding combination square, metric and imperial marking on ruler
Can mark 90° and 45°
Adjustable depth for repetition marking and scribing
Built in level bubble for approximate marking and a metal scriber contained in the end
Size: 300mm / 12"
Register to see prices 0.0 USD
Finger goniometer, stainless steel, JAMAR®
For Range of Motion (ROM) measurements of metacarpal, phalangeal and interphalangeal joints. Linear inch and centimeter markings on both sides of protractor in opposite directions. Protractor measures 0 degree to 150 degree in 5 degree increments.
Register to see prices 0.0 USD
Setting bevel stainless steel 300 mm
Precision machined edges and flat surfaces
Register to see prices 0.0 USD
External micrometer 0-25 mm
Carbide measuring surfaces finely lapped.
Measuring pin hardened and ground.
Blocking by lever.
With friction clutch and insulation.
With graduation of quality.
Metrology: Analogue / Packaging: Robust box / Standard: DIN 863 / ⌀ Spindle: 6.5 mm / Reading: 0.01 mm / Calibration: B1 / Measuring range: 0 mm - 25 mm / Micrometer scale: 1/50 mm / ⌀ micrometer drum: 18 mm
Register to see prices 0.0 USD
Protractor, 150 mm
Solid semicircular graduated arc with graduation 0 − 180°; reading 1°.
Scale plate non-glare chrome-plated. With clamping nut.
Register to see prices 0.0 USD
Vernier caliper 150 mm
Matte chromed anti-glare reading parts.
Fine graduation, high contrast.
Finely honed measuring surfaces.
Locking screw at the top.
Technical data
All parts: hardened / Depth gauge: flat / Metrology: analog / Locking: Locking screw on top / Thread table: Caliper table / Material: Stainless steel, INOX / Switchable reading: mm - inch / Graduation: 1/20 mm / Graduation: 1/128 inch / Allowable error: 0.05 mm / Standard: DIN 862 / Measuring range: 0 mm - 150 mm / Calibration: A1 / Packing: Case / Reading: 0.05 mm / Spout length: 40 mm
Register to see prices 0.0 USD
Footprint foam set
Very soft foam suitable even for children’s feet, with the best reproduction of contours.
- No crumbling
- Special German quality with great shape retention upon plaster pour
- No dusting even after a long period
Register to see prices 0.0 USD
Tripod for laser beam
Max. Length tripod = 900mm
Min. Length tripod = 200mm
Register to see prices 0.0 USD
Goniometre, long branches, stainless steel, JAMAR®
Professional-quality Goniometer feature clearly marked degree increments and easy-to-read inch and centimeter linear measurements.
Has two 180 degrees scales that read in opposite directions. 14" long. Scales marked in 10 increments. Non-locking friction arm.
Register to see prices 0.0 USD
Compensation board set
plastic, 6-part,
5 / 10 / 15 / 20 / 25 / 30 mm thick,
size 320 x 150 mm
Register to see prices 0.0 USD
Digital caliper 150 mm
Large high-contrast digital display. The measuring faces are precision-lapped.
Digital caliper with absolute scale, no zeroing required. Electronics switch off automatically after approx. 5 minutes. Simply move it to switch on.
Glass scale ensures very high accuracy.
The electronics are decoupled from the casing and incorporated directly in the sliding part. The gauging force is transmitted directly to the measurement jaws. This reduces the liability of the caliper to errors and increases the working life.
With sturdy metal casing.
Register to see prices 0.0 USD
Spirit level with magnet 250mm
Handy small spirit level. Die-cast aluminium profile. Face-milled measuring faces. Unbreakable acrylic vials (vertical + horizontal).
Additionally 360° rotating vial. Vee groove and magnet in the measuring face.
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Register to see prices 0.0 USD
Laser beam
Bosch Quigo, working area : 10 m
Register to see prices 0.0 USD
Try square Accuracy, 600X300mm
All faces and edges ground. Inspection test faces ground.
Application: For accurate general workshop work.
Accuracy: DIN 875 / 2 − angle tolerance e.g. for size 100×70 = 0.030 mm.
Standard: DIN 875
Stock length: 600×300mm
Right angle tolerance: 0.08 mm
Shank cross-section: 40×8 mm
Register to see prices 0.0 USD
Workshop vernier calipers with mm and inch graduations. 300 mm
Beveled measuring tips for measurements at the bottom of the thread and in narrow grooves. Rounded nose tips for interior measurements. Graduation with high contrast. With stop screw. Fully tempered to ref. 300, tempered measuring surfaces from ref. 500.
Material: Stainless steel, INOX / Metrology: Analog / Vernier graduation: mm / inches / Packing: Robust box / Graduation: 1/20 mm / Graduation: 1/128 inch / Locking: Locking screw on top / Switchable reading: mm / inch / Measuring range: 0 mm - 300 mm / Spout length: 90mm / Calibration: A1 / ⌀ Internal measuring shoulder: 10 mm / Standard: DIN 862 / Permissible error: 0.05 mm
Register to see prices 0.0 USD