Blade thickness: 0.4 mm
Blade length: 150 mm
TPI: 25

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Beveled measuring tips for measurements at the bottom of the thread and in narrow grooves. Rounded nose tips for interior measurements. Graduation with high contrast. With stop screw. Fully tempered to ref. 300, tempered measuring surfaces from ref. 500.
Material: Stainless steel, INOX / Metrology: Analog / Vernier graduation: mm / inches / Packing: Robust box / Graduation: 1/20 mm / Graduation: 1/128 inch / Locking: Locking screw on top / Switchable reading: mm / inch / Measuring range: 0 mm - 300 mm / Spout length: 90mm / Calibration: A1 / ⌀ Internal measuring shoulder: 10 mm / Standard: DIN 862 / Permissible error: 0.05 mm

The blanks are precision forged, ground and have an exact cut of even density and depth. After most careful tempering while hardening, these quality wood rasps/ files achieve the best performance and tool life.
Norm: DIN 7263
Cross section: 29×9 mm
Length without tang: 300 mm

The blanks are precision forged, ground and have an exact cut of even density and depth. After most careful tempering while hardening, these quality wood rasps/ files achieve the best performance and tool life.
Norm: DIN 7263
Cross section: 25×7 mm
Length without tang: 250 mm

Bailey chisel set in premium wooden box, lacquered beech wood handle with brass knuckles, forged blade with bevelled edges made of hardened steel, can be resharpened along the entire length, plastic cap to protect the cut in accordance with DIN 5139
sizes 6, 10, 15, 20, 25 mm

3 lines

also referenced under: EMACWELDWMBR, CRM 20

Wire thickness: 2.4mm, 8 wires

also referenced under: OOMAOWELPR04, CRM 5, 105.432

Welding mirror with Teflon coating and automatic temperature control. Suitable for indoor and outdoor use.

Diameter: 280mm
Weight: 3.0kg
Power consumption: 900 Watts / 230 Volts 50 Hz
Design: straight
Includes device stand.

also referenced under: OOMAOWELPR28, CRM 7, BARY A-2

230V/500W
High-end quality made in Switzerland

The TRIAC ST from Leister is a handy heat gun, primarily used as a profiling tool for welding and processing plastic membranes. Additionally, it is used for professional welding, shrinking and molding various thermoplastics. The two-sided air filters of the TRIAC ST can be easily removed and cleaned. This ensures an optimal air supply and maximum performance. As a successor of the TRIAC S, the ST combines a new, highly robust engine with current technology and modern design in a handy heat gun.

Compared to the design of other heat guns, the proven bar-style heat gun enables welding above the head, on the floor and in narrow areas. The ergonomic, two-component handle and its optimized center of gravity provide an ideal grip, even for longer periods of use and under difficult conditions. When in use, the actively cooled, protective tube ensures continuous safety by protecting against burns. The carbon brake also protects the heat gun from overloading. The extensive range of accessories with over 80 attachment nozzles practically make this heat gun a universal device. The TRIAC ST is already the seventh generation of Leister’s revolutionary line of TRIAC hot air tools. Decades of experience packaged in a modern design, manufactured with Swiss quality: The TRIAC ST is a robust and reliable tool.

VOLTAGE: 100 - 230 V
FREQUENCY: 60 Hz; 50/60 Hz
POWER: 1500 - 1600 W
TEMPERATURE: 40 - 700 °C
AIR FLOW (20°C): 240 l/min
TEMPERATURE SETTING STEPLESS: Yes
STATIC PRESSURE: 3000 Pa
NOISE EMISSION LEVEL: 67 dB (A)
OUTDOOR USE: Yes
DISPLAY: No
ECO MODE: No
E-DRIVE: No
NOZZLE CONNECTION Ø: 31.5 mm / 1.25 in; M14
LENGTH: 338.0 mm
DEVICE DIAMETER: 90 mm
HANDLE DIAMETER: 56 mm
WEIGHT: 0.99 kg
PLUG: KR, 2 poles, 16A; CN, 2 poles, 10A; EU, 2 poles, 16A; JP, 3 poles, 20A; CEE yellow, 3 poles, 16A; JP, 2 poles, 15A; AU, 3 poles, 10A; UK, 3 poles, 13A; US, 2 poles, 15A, polarized; CH T11, 2 poles, 10A
POWER CABLE LENGTH: 3.0 m
CONFORMITY MARK: CE
SAFETY MARK: KCC; S+; UL
PROTECTION CLASS: II

also referenced under: OOMAOWELAIRT, CRM 1, 141.311

- Closed-loop controlled temperature
- Open loop controlled air volume
- Intelligent «e-Drive» operating unit
- Ergonomic handling
- Modern design/ Swiss made
Power W: 1600
Voltage V~: 230
Temperature °C: 45 - 620
Air volume (20°C) l/min: 160 - 240
Size (L x ∅) mm: 335 × 90
Handle ∅ mm: 56
Weight kg: 1

- 100% Swiss made quality
- 60 years of expertise in making hot-air tools – brought together in the new SOLANO AT
- The sturdy, professional hot-air tool that weighs less than 1 kg/2.18 lbs
- Functional design: two-component handle grip and optimum center of gravity ensure ergonomic working
- Quick clean air filters
- Automatic carbon stop (collector protection) and heating element protection
Voltage V ~: 230
Power W: 2300
Temperature ° C: 500–650
Air quantity (20 ° C) l / min: 240
Dimensions (L × ∅) mm: 270 x 270 x 75 (45)
Weight: 750gr

• 100% Swiss made quality
• Leister's smallest manual device
• Continuous electronic temperature control
• Continuous electronic adjustment of the air flow
• Quiet
• Integrated flexible foot
Voltage V ~: 230
Power W: 460
Temperature ° C: 40-600
Air flow (20 ° C) l / min: 40/110
Dimensions (L × ∅) mm: 235 x 70
Weight: 400gr

also referenced under: OOMAOWELHJ01, CRM 1.0, 100.688

Box joint (= double guides). Designed to prevent fingers being trapped. Induction hardened. Notched serrated jaws, adjustable in stepped holes. Multi-position ratchet adjustment.
Red powder-coated, polished jaws and joint.
Standard: DIN ISO 8976
Material: Chrome vanadium steel, drop forged.
overall length: 250 mm
Hexagon across flats: 36 mm
Jaw capacity for pipes: 1.1/2 inch

2-component holder (up to size 3-20) with pistol handle with exchangeable precision ground punch cutters. For the production of gaskets two punch cutters of different ⌀ are inserted together in the holder.
For punching or manufacturing discs / rings in one operation. For rubber, leather, felt, plastic, cork, fabric or similar materials.
1 each circle cutter ⌀: 55−330 mm
Centring point No. 832140: 1 pc.
1× each punching tool ⌀ No. 832110: 15 pcs.
size 3; 4; 6; 8; 10; 12; 14; 16; 18; 20; 22; 24; 26; 28; 30
Available combinations of punches inner : outer (mm): 3−10 inner with 12−30 outer 12−20 inner with 22−30 outer
Container length×width×height (mm): Plastic 275×205×50
Use an underlay of wood, leather etc. when punching to avoid damage.
The following combinations are not possible: 20 (inner) with 22 (outer); 30 (inner) with 32 (outer); 40 (inner) with 42 (outer); 50 (inner) with 52 (outer).

2-component holder (up to size 3-20) with pistol handle with exchangeable precision ground punch cutters. For the production of gaskets two punch cutters of different ⌀ are inserted together in the holder.
For punching or manufacturing discs / rings in one operation. For rubber, leather, felt, plastic, cork, fabric or similar materials.
1× each punching tool ⌀: 10 pcs.
size 3; 4; 6; 8; 10; 12; 14; 16; 18; 20
Available combinations of punches inner : outer (mm): 3−10 inner with 12−20 outer
Container length×width×height (mm): Plastic 140×100×40
Use an underlay of wood, leather etc. when punching to avoid damage.
The following combinations are not possible: 20 (inner) with 22 (outer); 30 (inner) with 32 (outer); 40 (inner) with 42 (outer); 50 (inner) with 52 (outer).

Heavy-duty, heavy-duty, steel / die-cast construction. Very low vibrations and precise guidance thanks to CNC machined components. Very powerful clamping thanks to the special clamping device. An integrated compressed gas spring ensures that the weight is balanced when adjusting the height of the vice. Locking in any position by means of a safety clamping lever.
The vise can be rotated 360 ° in conjunction with the vertical mover without an additional swivel base to bring a workpiece into the most favorable working position. The safety clearance required by DIN 31001, part 1 (25 mm) is thus observed for all oscillation and movement movements in height.
To adapt the vice to the nearest centimeter to the ideal working height (particularly important for learning and training workshops).
Delivery:
Fixing screws included for bench mounting.
Height adjustment range: 242 mm
Adjustable on a bench table: 93 mm - 335 mm
Weight: 11.2 kg

Strong base with lapped standing surface. Reading 0.02 mm with fine adjustment. The scriber is carbide tipped. With adjustable measuring beam, magnifying glass and locking screw.
Metrology: Analogue / Material: Stainless steel, INOX / Surface base, Length: 135 mm / Tracing height: 300 mm / Vernier: 1/50 mm / Calibration: E1 / Base area, width: 90 mm / Rule section: 28 × 9 mm / Allowable error: 0.06 mm

Matte chromed anti-glare reading parts.
Fine graduation, high contrast.
Finely honed measuring surfaces.
Locking screw at the top.
Technical data
All parts: hardened / Depth gauge: flat / Metrology: analog / Locking: Locking screw on top / Thread table: Caliper table / Material: Stainless steel, INOX / Switchable reading: mm - inch / Graduation: 1/20 mm / Graduation: 1/128 inch / Allowable error: 0.05 mm / Standard: DIN 862 / Measuring range: 0 mm - 150 mm / Calibration: A1 / Packing: Case / Reading: 0.05 mm / Spout length: 40 mm

Serrated jaws. Cutting edges additionally induction hardened (approx. 64 HRC); suitable even for piano wire.
Jaws bright finished, plastic coated handles.
Standard: DIN ISO 5746
Material: Chrome vanadium steel, drop forged.
overall length: 160 mm
Cutting capacity hard wire up to ⌀: 2 mm
Cutting capacity piano wire up to ⌀: 1.5 mm
Jaw characteristics: inner face serrated
Handle: plastic coated
Manufacturing process: Cutting edges induction hardened (approx. 64 HRC), pliers body drop forged
Material: Chrome vanadium steel

Workbench in sturdy steel construction. 50 mm wide base with reinforcement. Feet with non-marking plastic glides. With 1 pair of gussets to ensure rigidity. 16G drawer unit with central locking by cylinder lock. Full extension drawers with differential slides and load capacity of 75 kg.
Workbench height: 850 mm
Permissible load of drawers / extendable shelves: 75 kg
Permissible work bench / table load - Maximum load per rack distributed over the surface (on the wood): 400 kg
Worktop thickness: 50 mm
Drawer extraction (partial / total): 100%
Usable drawer surface in G: 12 × 20
Worktop length: 1,500 mm
Worktop depth: 750 mm
Height of drawer unit: 300 mm
Width of drawer unit: 400 mm
Depth of drawer unit: 650 mm
Useful height of drawer unit: 225 mm
Useful width of drawers: 300 mm
Useful depth of drawers: 500 mm
Number of drawers: 2
Weight: 82 kg

Serrated jaws and powerful steel spring clamp body. Distance and clamping pressure adjustable via a knurled screw. Nickel plated pliers.
Oval jaw shape

Serrated jaws and powerful steel spring clamp body. Distance and clamping pressure adjustable via a knurled screw. Nickel plated pliers.
Oval jaw shape

Serrated jaws and sturdy spring steel body. Span and clamping pressure adjustable with a knurled screw. Fully nickel-plated.
Jaw shape double Vee.
For clamping profiled and flat materials. Clamping force up to 10,000 N.
Material: Jaws of chrome vanadium steel, drop forged.
Jaw capacity: 40 mm
overall length: 250 mm
Jaw length: 35 mm

Inside serrated.
Of special steel, nickel-plated (No. 727520 / 7560 painted black).
Length: 150 mm
Tip characteristics: narrow/angled, inner face serrated
Point form: 22b
Surface of tweezers: nickel-plated
Tip exchangeable: no

Striated inside

Lightweight and durable magnesium metal body with needle bearing and thumbwheel guide rollers. Hand deburrer retractable in the body. With spare rollers.
Advantages):
Automatic hold and tightening on the tube thanks to the quick one-hand QuickLock adjustment.
Quick and precise positioning of the wheel according to different tube diameters.
Use:
Universal for cutting thin-walled stainless steel, copper and aluminum tubes (up to 2 mm thick).
Technical data
For ⌀ ext. pipe: 6mm - 35mm

All faces and edges ground. Inspection test faces ground.
Application: For accurate general workshop work.
Accuracy: DIN 875 / 2 − angle tolerance e.g. for size 100×70 = 0.030 mm.
Standard: DIN 875
Stock length: 600×300mm
Right angle tolerance: 0.08 mm
Shank cross-section: 40×8 mm

Max. Length tripod = 900mm
Min. Length tripod = 200mm

270mm

The tapered Torx® HF profile reliably retains all Torx® screws. L-shank; through hardened (hard and tough).
Ideal for starting and tightening Torx® screws where access is difficult.
Material: Chrome vanadium steel, manganese phosphated.
Supplied with table use:
1 each L-wrench in a plastic clip: TX8; TX9; TX10; TX15; TX20; TX25; TX27; TX30; TX40

Clés dynamométriques à un bras sans vernier de réglage. Réglables par un appareil de contrôle de clé dynamométrique

Kraftform handle for easy transmission of the required torque. With Rapidaptor quick-change holder for 1/4 inch bits with C6.3 and E6.3 shank. Sizes 600 and 880 with pistol grip for transmission of higher torques.
The torque can be set using a torque analyser (No. 654300 − 654460) and a 7AF hexagon screwdriver (10AF for size 600) . The torque screwdrivers are factory-set to the most frequently used torque setting.
When the set torque is reached the screwdriver triggers, with clearly audible and perceptible signals. The triggering torque is unrestricted.
maximum torque: 120 cN·m
set torque: 0.3 N·m
Bit socket: D6.3 ; F6.3
Torque range:0.3 N·m - 1.2 N·m
Connection format: bitholder 1/4 tomme
Overall length L: 155 mm
Adjustable trigger value: pre-set

139 tools

This vise tilts 90 degrees and is solidly constructed. Thanks to its excellent clamping force, the vice does not move when drilling or milling.
Made of cast iron, the vise is strong and sturdy. This vise has an adjustable tilt angle between 0 and 90 degrees, and a locking pin on the chain to secure it every 15 degrees.
This unit also features a stable base, which can be easily mounted on your workbench. It is compact and lightweight, making it suitable for mobile use.

Specifications
Material: cast iron
Jaw width: 105mm
Jaw opening: 110 mm
Jaw depth: 47mm
Base size: 190 x 185 mm (L x W)
Tilt adjustment: 0 - 90 degrees
Height: 120mm (lying), 220mm (standing)

The blanks are forged and ground; manufactured with an exact cut of even density and depth using special machines. These non-convex files have tooth profiles appropriate to each grade of file.
Cuts on all faces; convex end.
The quality file for workshop use with long tool life and high removal rate.
Standard: DIN 7261 form C
Length without tang: 250 mm
Width: 18 mm

also referenced under: OOMAMARP3000F, CRM 95

Tape measure of light quality, for everyday use. Yellow/white ribbon in polyfiber fabric with black graduation on both sides. Metal tip at both ends.
Length: 150cm
Width: 18.5mm

With hardened jaws and steel handles. Possibility of removing a handle to allow use in confined spaces.
Reinforced model. All dimensions with high quality forged steel body and solid steel handles.
□ capacity: 3 mm - 9 mm
For hand taps DIN 352: M4 - M12
For ⌀ hand reamers DIN 206: 5 mm - 10 mm
Total length: 280 mm

With hardened jaws and steel handles. Possibility of removing a handle to allow use in confined spaces.
For normal use: cast zinc body.

Packaged in a blue plastic box with pilot drills
Content :
1 set of HSS hand taps each:
DIN 352 M 3 / 4 / 5 / 6 / 8 / 10 / 12
1 HSS die of each DIN 223:
M3 / 4 / 5 / 6 / 8 / 10 / 12
HSS twist drills, DIN 338 N, ground:
Ø2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2mm
1 die holder DIN 225:
20x5 / 20x7 / 25x9 / 30x11 / 38x14
1 left hand wrench DIN 1814:
Group 1 + 2

Square drive: 3/8 in
Total length: 200mm