25m

25m

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Set of 3 sheets
Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

Can be shaped easily.
Can be worked with hot water or with a heat gun.
Perfectly matches the patient's shapes.
Good weldability.
Lightweight and resistant.
Can be used on a model or directly on the patient who has been previously protected with Jersey.
> For finger and wrist splints

1000x1600mm

These sealants replace hemp, sealing tapes, and pastes, they are resistant to gases, liquids, air, water, oils, hydrocarbons and many chemical products. Complete surface contact ensures a 100% seal. Unscrewing, or correction of position during assembly can be performed using conventional tools at any time before the sealant hardens. No sealant residues to block filters and valves.
The stick with pasty sealant is economical in consumption, no drips after use.
Application:
Improved bonding of suckers.
Note:
Before applying sealant, clean the threads with general-purpose cleaner
Labelling of hazardous substances: GHS07 Caution
Content of stick: 19 g
Colour of sealant: orange
minimum break-away torque: 5.8 N·m
Temperature range: -55 °C - 150 °C
for thread size M to: M80
for imperial thread size: 3 inch
Strength for disassembly: low
fluorescent:no

50 cm

Its texture allows it to breathe and to drain perspiration.
Very comfortable and soft to the touch
Easy to clean, washable at 40°C / 100°F.
Good ageing
Glue-less, this fabric complies with sustainable development policies and limits risks of allergy
Thermoformable at 170°C / 340°F.

Its texture allows it to breathe and to drain perspiration.
Very comfortable and soft to the touch
Easy to clean, washable at 40°C / 100°F.
Good ageing
Glue-less, this fabric complies with sustainable development policies and limits risks of allergy
Thermoformable at 170°C / 340°F.

400x400x15mm
Suitable for fabricating flexible inner prosthetic sockets,
especially in lower limb prosthetics
Product information:
• Ethylene vinyl acetate
• Also in antibacterial (616T253)
• High flexibility
• High surface quality
• Can be subsequently thermoformed
• Minor shrinkage: approx. 3%
• Comfortable to wear
• Washable
• Temperature recommendation: 160 °C/320 °F
(convection oven, infrared oven)

9x400x400mm, ethylene vinyl acetate (EVA), moldable at approx. 130-135 °C, suitable for flexible inner sockets, especially for above-knee sockets

14x400x400 mm, ethylene vinyl acetate (EVA), moldable approx. 130-135 ° C, suitable for flexible internal sockets, in particular for sockets above the knee

12x400x400mm, ethylene vinyl acetate (EVA), moldable at approx. 130-135 °C, suitable for flexible inner sockets, especially for above-knee sockets

- ethylene vinyl acetate (EVA)
- for shoe-insoles
- for water-resistant splints and supports
- for hand (metacarpus) splints and forerarm splints
- in arm prosthetics, for foot prostheses (e. g. according to Bellmann)
- for prostheses sockets

permanently elastic thermoforming film, moulding temp: 120-135 °C / 248-275 °F

permanently elastic thermoforming film, moulding temp: 120-135 °C / 248-275 °F

2.5x1740x960mm

Acrylic resin is very fluid, allowing, in combination with COPACRYL Jersey or COPACRYL Carbon resins, to add flexibility to composite parts.

The Soft resin cannot be used alone and must be incorporated into the Jersey or Carbon resin at a ratio of 10 to 30% to add flexibility to the fabricated device.

The polymerization of this resin occurs at room temperature by adding our SIPACRYL powder hardener, at a maximum ratio of 2% to 3% by weight compared to the amount of resin.

Combining COPACRYL Soft resin with Jersey or Carbon resins yields composite parts with the following characteristics:

Excellent mechanical properties
Very good skin tolerance
Ability to be thermoformed after curing (within the elasticity limits of the reinforcement fabrics used)
Can also be used with our natural reinforcements ORTHOFLAX®, ECO-BLACK, and HYBRIDS.

Stretchable, breathable, comfortable 3D fabric
Waterproof thanks to the associated flexible film
Very comfortable and soft to the touch
Ideal for making covers with waterproof areas.
Easy to clean, washable at 30°C/86°F without spinning

Stretchable, breathable, comfortable 3D fabric
Waterproof thanks to the associated flexible film
Very comfortable and soft to the touch
Ideal for making covers with waterproof areas.
Easy to clean, washable at 30°C/86°F without spinning

100pc
Application:
for manufacturing of closures for orthopaedic shoes

Color white-transparent, water and oil resistant, resistance to the action of most chemicals, NLGI consistency class 2-3, -40 ° C - + 200 ° C, non-toxic.
For lubrication between metal and plastic or metal and elastomer, lubricating grease for valves, O-rings and ball valves

Color white-transparent, water and oil resistant, resistance to the action of most chemicals, NLGI consistency class 2-3, -40 ° C - + 200 ° C, non-toxic.
For lubrication between metal and plastic or metal and elastomer, lubricating grease for valves, O-rings and ball valves

6x920x850mm

4x920x850mm

3x800x800mm

When sprayed, the Teflon ™ / PTFE microparticles ensure clean dry lubrication without oil-covered hands, adhesive protection and effective reduction of static, dynamic and rolling friction.
Dry lubrication and hygienic solid.
No adhesion of dirt and dust on the treated surface.
No formation of annoying lubricant residues.
Oil and fat free.
Hygienic, clean and ecological.
Durable and resistant lubrication and sliding effect.
Resin-free, non-hardening.
High material compatibility (all metal and plastic parts!).
Silicone and acid free.
Execution: Aerosol can
Content: 0.4 l
Color: transparent
Boiling point: 78 ° C
Flash point: -104 ° C
Auto-ignition temperature: 400 ° C
Water solubility: insoluble
Signaling of hazardous substances: SGH02 Flammable
Class of dangerous goods: 2.1
UN number: UN1950

Glass-hard resin with very good adhesive properties