Sheet steel cabinet body with integrated door locking system, interior body with chemical resistant surface.
Shelving for 32 mm pitch shelves.
Ground retention tank (according to StawaR).
With exhaust air connection (NW 75).
With door locking system.
Lockable with a profile half-cylinder, can be integrated into a house lock. Not compatible with the Hoffmann locking system.
With 4 adjustment elements to compensate for slight unevenness in the floor.
2 doors
Correct storage of flammable hazardous products in work rooms.
Standard: DIN EN 14470-1, type test (tested in a fire chamber), 90 minutes fire resistance.
Delivery: Cabinet with 3 shelves, a perforated sheet metal plate and a holding tank on the floor, plastic covering, 1 service booklet.
Colors: Cabinet body and doors in light gray RAL7035 or signal yellow RAL1004, powder-coated.
Note (s): Safety cabinets should be subject, at regular intervals (annually), to appropriate maintenance and verification of their proper functioning by a competent person.
Height adjustment in 32 mm steps
Fire resistance: 90 min
Height: 1,968 mm
Width: 1,196 mm
Depth: 616 mm
Number of shelves: 3
Permissible shelf load: 75 kg
Number of retention basins on the ground: 1
Volume retention tank on the ground: 33 l
Weight: 453 kg

Housing for drawers, shelves, etc. possible in steps of 20 mm. The base and upper cabinets are provided with corresponding perforations for screwing together, equipment with castors (height 1200 mm max.) Or wall mounting.
Doors with safety edges, reinforced and rigid, hinged or sliding door available, solid sheet model or with polycarbonate manhole. The cabinet without doors can also be used as open shelving.
Cylinder locks with 2 keys each integrated in the sliding handle. On request, possibility of delivery of locks for installations with security card at an additional cost.
Colors: As standard, body in light gray RAL 7035, doors and drawers in signal blue RAL 5005, powder-coated.
Cabinets fitted directly or subsequently with drawers must be anchored to the floor or to the wall to avoid any risk of tipping and may under no circumstances be subsequently fitted with casters.
In the case of specific equipment, make sure that the sum of the mounting heights does not exceed the useful height of the cabinet.
Shelves and accessories for combinable cabinets, see art codes. 957000 - 957100.
Installation of drawers in the upper part of the cabinet for base cabinets and in the lower part of the cabinet for upper cabinets.
Material thickness: 0.9mm
Permissible load of drawers / extendable shelves: 60 kg
Permissible shelf load / Maximum load per rack distributed over the surface (on the metal): 100 kg
Allowable load internal cabinet body: 1000 kg
Drawer extraction (partial / total): 100%
Door opening angle: 225 degree
Height adjustment in steps: 20 mm
Cylinder lock: Modular cylinder
Available colors: RAL 9002, 7035, 7005, 7016, 6011, 5018, 5012, 5011, 5005, 3003
Safety certificate: GS TÜV Süd
Height: 800 mm
Width: 500mm
Depth: 550 mm
Useful height: 640 mm
Weight: 30 kg

510 x 380 x 550 mm

steel

Stand of sheet metal 40×40 mm for screwing to the worktop. Perforated sheet metal panel between the columns.
Colour:
RAL 7035 light grey powder coated.
Note:
Articles in the support column attachment range cannot be inserted into the perforated panel.
Technical Data
Material thickness: 1 mm
Hoffmann perforated panel grid interval: 9×9 mm
Height: 481 mm
Width: 1,420 mm
Depth: 25 mm
suitable for type: 1500

Silver-anodised aluminium frame with white enamelled surface. The board is washable, can be written on and is magnetic. With storage bar.
Ideal for temporary notices. Easy mounting in portrait and landscape format, with mirror attachment sockets or by the corners.
Height: 1000mm
Width: 1500mm
Material of the surface: Aluminium
Colour of frame: silver anodised
Colour of board: painted white
For use in landscape and portrait view: yes
Board for writing on: yes
Board for magnetic clamps: yes
Weight: 6.5 kg

Measuring jug set of transparent polypropylene, resistant to oil and acid. Scale with ml divisions, ergonomic handle, stackable.
Supplied with:
1 measuring jug 0.5 litre, scale division 10 ml.
1 measuring jug 1.0 litre, scale division 10 ml.
1 measuring jug 2.0litre, scale division 20 ml.

Board writers with pigmented ink, no odour, wipe off dry. Magnetic cap with integral rubber. 4 pieces, assorted colours: red, black, green and blue. With anti-bacterial coating for a high degree of infection prevention. Line thickness:1 – 3 mm. 3 days cap-off time. Up to 30% of recycled material.

Garbage bag made of premium low density polyethylene with reinforced thickness.
Bellows bags with closing link, adaptable to all types of garbage cans and collectors.
Optimal resistance to falling and breaking of the closing link.
The tightness of the welds allows safe handling.

Film thickness: 100 µ.
Volume: 110 liters.
Color Black.

hardly flammable, without plasticizer, adhesion maintained also at low temperature

Treads and stiles made of extruded aluminium sections.
Treads 85 mm deep with safe, non-slip serrated surfaces and patented 7-point tread-stile connection.
Especially light and easy to carry, with smooth stile surfaces that are comfortable to hold.
External width: 400 mm
Ladders and platforms load capacity: 150 kg
Width: 400 mm
Ladder length: 2.99 m
Working height approx.: 3.9 m
Cross beam height: 87 mm
Tread depth: 85 mm
Number of steps: 12
Material: Steps and stiles made of extruded aluminium sections

Large wheelie bin in tapered plastic body shape. Stabilising ribs at the top edges. Cover with all-round sealing lip for condensate. The lid handles are easy to hold and are arranged obliquely. 4-piece hinges (size 80: 2-piece hinges) with hinge pin retainers. Reinforced base with patented arrangement of axles. Sturdy external chassis with robust reinforced axles and free-running wheels. Noise-suppressed cover opening satisfies the noise reduction regulations to the EU directive 2000/14.
Enhanced container stability due to special design of the base, with through axle contour.
Volume: 120 l
Height: 1,005 mm
Width: 480 mm
Depth: 555 mm
Wheel ⌀: 200 mm
Colour: blue

Width of the jaws: 150mm
Opening of the vice: 130 mm
Height of the jaws: 40 mm
Between axis: 160 mm
Overall dimensions WxDxH: 450x450x160 mm
X axis, longitudinal stroke: 200 mm
Y axis, transverse stroke: 200 mm

Silver-anodised aluminium frame with white enamelled surface. The board is washable, can be written on and is magnetic. With storage bar.
Ideal for temporary notices. Easy mounting in portrait and landscape format, with mirror attachment sockets or by the corners.
Height: 600 mm
Width: 900 mm
Material of the surface: Aluminium
Colour of frame: silver anodised
Colour of board: painted white
For use in landscape and portrait view: yes
Board for writing on: yes
Board for magnetic clamps: yes
Weight: 2.5 kg

Allowable shelf load: 150 kg
Dimensions: 1000x500x25mm

Casings and doors made of 0.9 mm sheet steel, shelves can be accommodated in steps of 40 mm. Reinforced doors internally and lockable by a sliding handle with cylinder lock. Complete with 4 shelves in galvanized sheet metal.
RAL 7035 light gray body, RAL 7016 anthracite doors, powder coated.
Cylinder lock
Allowable load interior cabinet body: 500 kg
Permissible shelf load / Maximum load per rack distributed over the surface (on the metal): 80 kg
Width: 950mm
Depth: 430mm
Height: 1950 mm

Aluminium five-point star base (⌀ 580 mm). Continuous height adjustment by gas pressure spring. Seat of SoftTouch PU foam with ribbed profile. Soft seat with non-slip surface, ribbed profile allows air circulation (climate comfort). Ergonomic backrest (height 190 mm) supports correct posture. PU foam, soft, comfortable, washable.
Application:
Ideal combination of standing and sitting. For use at sitting or standing workstations, or a combination of both.
Work stool version with castors for hard floors.

⌀: 310mm
Height: 320mm

Ideal for storing plaster molds and models
Allowable shelf load: 150 kg
Number of shelves: 5
Dimensions: 1060x536x2000mm
Total maximum load: 1300 kg

High quality malleable cast iron clamping arms; strong prismatic steel slide beam, knurled, electro-galvanised. Low friction steel spindle, burnished with trapezoidal thread and movable jaw. Instant (high speed) adjustment, reliable clamping. Up to size 400 with plastic protective cover on the clamping jaw, from size 500 onwards without protective cover.
Standard: DIN 5117
Cross section of the slide rail: 35×11 mm
Throat: 120 mm
Jaw capacity: 500 mm

Coating of a modified acrylic adhesive, resistant to light and aging. The adhesive is highly resistant to plasticizers and features a high initial adhesive strength and good shear resistance. Applications include mounting signs, nameplates, reinforcing doors in the automotive industry, attaching plastic bags, continuous paper and poster mounting, and joining paper and film rolls.

Width of the jaws: 100mm
Opening of the vice: 100 mm
Height of the jaws: 27 mm
Between axis: 130 mm
Overall dimensions WxDxH: 165x190x57 mm
Weight: 2.7kg

Entirely made of steel, unbreakable. Foldable form with self-closing coupling hooks

139 tools

The stable sheet metal construction of the roller cabinet includes an ABS tray and push handle. Drawer unlocked by lifting the drawer.
Placement:
Drawer front height: 60; 60; 60; 120; 120; 120; 180 mm
Supplied with:
Dividing material. 12 divider partitions 410 mm.
Colour:
Two-tone powder-coated. RAL 7035 light grey combined with RAL 7016 anthracite grey.
Drawer/pull-out shelf load capacity: 15 kg
Drawer runner extension (partial/full extension): 75 %
Hoffmann perforated panel grid interval: 9×9 mm
Cylinder lock: modular lock barrel
Height: 1,005 mm
Width: 720 mm
Depth: 450 mm
Drawer usable width: 530 mm
Drawer usable depth: 410 mm
Number of drawers: 7
Weight: 50.3 kg

Made of polypropylene - light, robust and shockproof. Resistant to most acids and bases. Padlock closure, 5 handle 5 mm
Volume: 20 l
239x474x190 mm
Weight: 1.9 kg
Number of variable lockers: 6

Sheet steel drawer units. Central closure by cylinder lock. Drawers with large aluminum handle bar and label holder, extendable up to 90%. Interior with notched walls for compartmentalization of drawers.
Established load capacity / table - Maximum load per compartment distributed over the surface (on the wood): 2,000 kg
Worktop thickness: 50 mm
Established height: 850 mm
Worktop material: Beech plywood
Usable width of drawers: 490 mm
Drawer cabinet depth: 630 mm
Usable depth of drawers: 520 mm
Width of drawer unit: 600 mm

Worktop 50 mm thick. Holes are provided for fixing drawers and legs.
Base in sturdy U-shaped steel profile. Drawer unit with 720 mm useful height and central closure. Equipped with 5 drawers (partial extraction).
Worktop in beech plywood, glued, waterproof. With colorless UV varnish.
Drawer units 600 mm wide in sheet steel with cylinder lock with 2 keys and central locking. Sheet steel drawer with large aluminum handle bar, extendable up to 90%. Designed for compartmentalization. The drawer units can be mounted on the right, left or in the center of the worktop. For a plan length of 1500 mm, possibility of mounting 2 - 3 boxes, for a plan length of 2000 mm, possibility of mounting 3 - 4 boxes (depending on the width of the boxes).
Legs in folded sheet steel (80 mm wide), with reinforcements.
Drawer units to be mounted on the right or on the left.
Front height of drawers: 60; 100; 140; 180; 240 mm
Colors: RAL 7035 light gray body and feet, RAL 5005 signal blue drawers, powder-coated. For other paintings, price on request.
Note (s): Delivery by separate elements, more economical. Delivery without assembly.
Established height: 850 mm
Allowable load of drawers / extendable shelves: 100 kg
Established load capacity / table - Maximum load per compartment distributed over the surface (on the wood): 1,000 kg
Worktop thickness: 50 mm
Drawer extraction (partial / total): 90%
Cylinder lock: Modular cylinder
Safety certificate: GS TÜV Süd
Worktop length: 1,500 mm
Worktop depth: 700 mm
Worktop thickness: 50 mm
Drawer cabinet height: 800 mm
Drawer cabinet width: 600 mm
Drawer cabinet depth: 630 mm
Usable width of drawers: 490 mm
Usable depth of drawers: 520 mm
Number of drawers: 5
Worktop material: Multiply beech
Worktop surface: colorless varnish

Worktop 50 mm thick, robust, in beech plywood, water resistant, colorless UV varnish. Support legs of folded sheet metal (80 mm wide), with cross braces.Colors: RAL 7035 light gray tubes, powder coated.
Worktop thickness: 50mm
Established admissible load / table - Maximum load per compartment distributed over the surface (on the wood): 400 kg
Worktop depth: 700 mm
Worktop thickness: 50 mm
Worktop length: 1500 mm
Established height: 850mm

Worktop 30 mm thick, robust, in beech plywood, water resistant, colorless UV varnish. Frame in screwed square tubes (30 × 30 mm), with plastic glides.
Colors: RAL 7035 light gray tubes, powder coated.
Worktop thickness: 30mm
Established admissible load / table - Maximum load per compartment distributed over the surface (on the wood): 250 kg
Worktop depth: 700 mm
Worktop thickness: 30 mm
Worktop length: 1500 mm
Established height: 850mm

Worktop 50 mm thick. Holes are provided for securing drawer units and support legs.
Worktop of beech marine ply, with waterproof glue. Finished with clear UV varnish.
Drawer unit 600 mm wide of sheet metal with cylinder lock with 2 keys and central lock. Drawer units can be mounted on the right, left or centre of the worktop. Worktops of 1500 mm can accept 2 − 3 units, worktops of 2000 mm can accept 3 − 4 units (depending on the width of the units). Drawers of sheet metal with wide aluminium grip handles. − Can be pulled out 90% − With slots for drawer dividers on the inner faces.
Support legs of folded sheet metal (80 mm wide), with cross braces.
Fitted with:
Drawer front height: 60; 80; 100 mm
Supplied for self-assembly, saving freight costs. Delivered unassembled.
Technical Data
Material thickness 1 mm
Workbench height 850 mm
Drawer/pull-out shelf load capacity 100 kg
Workbench/desk load capacity - maximum distributed load (on wood) 400 kg
Insert thickness 50 mm
Drawer runner extension (partial/full extension) 90 %
Cylinder lock modular barrel
Safety certificate GS TÜV Süd
Series KOMBI workbench
Height: 850mm
Worktop length: 1,500mm
Worktop depth: 700mm
Worktop thickness: 50mm
Drawer body height: 300mm
Drawer body width: 600mm
Drawer body depth: 630mm
Drawer usable width: 490mm
Drawer usable depth: 520mm
Number of drawers: 3
Material of worktop: Beech marine ply
Surface worktop: clear varnished

Worktop 50 mm thick. Holes are provided for securing drawer units and support legs.
Worktop of beech marine ply, with waterproof glue. Finished with clear UV varnish.
Drawer unit 600 mm wide of sheet metal with cylinder lock with 2 keys and central lock. Drawer of sheet metal with wide aluminium grip handles, can be pulled out 90 %. With slots for drawer dividers on the inner faces. Drawer units can be mounted on the right, left or centre of the worktop. Worktops of 1500 mm can accept 2 − 3 units, worktops of 2000 mm can accept 3 − 4 units (depending on the width of the units).
Support legs of folded sheet metal (80 mm wide), with cross braces.
Rear panels of folded sheet metal, 25 mm deep.
Fitted with:
Drawer front height: 60; 80; 100 mm
Supplied for self-assembly, saving freight costs. Delivered unassembled.
Technical Data
Material thickness 1 mm
Workbench height 850 mm
Drawer/pull-out shelf load capacity 100 kg
Workbench/desk load capacity - maximum distributed load (on wood) 800 kg
Insert thickness 50 mm
Drawer runner extension (partial/full extension) 90 %
Cylinder lock modular barrel
Safety certificate GS TÜV Süd
Series KOMBI workbench
Height 850 mm
Worktop length: 1,500 mm
Worktop depth: 700 mm
Worktop thickness: 50 mm
Drawer body height: 300 mm
Drawer body width: 600 mm
Drawer body depth: 630 mm
Drawer usable width: 490 mm
Drawer usable depth: 520 mm
Number of drawers: 3
Material of worktop: Beech marine ply
Surface worktop: clear varnished

Made of folded sheet metal, 25 mm high.
Application:
As shelf and as additional bracing.
For installation between two support legs.
Colour:
RAL 7035 light grey powder-coated.
Technical Data
Material thickness 1 mm
Series KOMBI-filebænk
Width 1,340 mm
Depth 2-part 630 mm
suitable for worktop length 1,500 mm
Load capacity, distributed 300 kg

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Made entirely of forged steel − guaranteed unbreakable.
Opens forward. With forged pipe jaws underneath the normal jaws

Heavy-duty, heavy-duty, steel / die-cast construction. Very low vibrations and precise guidance thanks to CNC machined components. Very powerful clamping thanks to the special clamping device. An integrated compressed gas spring ensures that the weight is balanced when adjusting the height of the vice. Locking in any position by means of a safety clamping lever.
The vise can be rotated 360 ° in conjunction with the vertical mover without an additional swivel base to bring a workpiece into the most favorable working position. The safety clearance required by DIN 31001, part 1 (25 mm) is thus observed for all oscillation and movement movements in height.
To adapt the vice to the nearest centimeter to the ideal working height (particularly important for learning and training workshops).
Delivery:
Fixing screws included for bench mounting.
Height adjustment range: 242 mm
Adjustable on a bench table: 93 mm - 335 mm
Weight: 11.2 kg

high-quality masking tape for painters, plasterers and bodywork painters, up to 80°C, well-impregnated reinforcement or very good resistance to re-sanding, also ideal for dispersion paints

Technical characteristics
Radius of curvature (middle tube): 45; 50; 65; 100; 130; 150; 200mm
Maximum thickness: 5.5 mm
Max bending angle: 90 degree
For nominal pipe sizes: 3/8 – 2 inch

Heavy-duty hydraulic tube bender with closed hydraulic system and return spring for better piston control. Cast iron pads and shapes, powerful piston delivering a pressure of 450 bars. High quality piston seals prevent leakage and increase service life. Skates with bending angle indication. Safe bending of tubes thanks to closed flange. The special design of the lever ensures protection against overloads. Delivery in a resealable wooden box.

Use:
For bending galvanized and black steel tubes as well as gas tubes (3/8 inch − 2 inch). Max. bending angle 90°, tubes max. 5.5 mm thick (2 inch tubes). Easy actuation thanks to the long piston stroke with each pump. Universal use in mechanical engineering, for work on pipeline systems, locksmithing, etc.

Content:
1 form of each: Ref. 3/8; 1/2; 3/4; 1; 1.1/4; 1.1/2; 2
Skate 2 pc.
Hydraulic tube bender: 1 pc.
Wheels: 3 pcs.

The 3M™ GPT-020F double-sided tape is characterized by high moisture resistance, very high immediate adhesion, excellent shear strength, even at high temperatures, as well as good UV resistance.