T-PLATE foot pressure plate is the most accurate and cost-effective way to identify the plantar pressure profile.
Traditional tools cannot provide the same information as the T-Plate. It will increase your credibility and most of all help you make the good diagnosis.
Deliver with software and manual in English.

The slideable T-handle is fitted with an end-stop to ensure it does not slide out.
With swivel jointed head (torsion drive 50°, swing drive up to 90°). The swivel angle is secured by an integral spring.
Material: Chrome vanadium steel, chrome-plated.
Drive profile: Hexagon socket
Wrench length: 450 mm
Width across flats: 17 mm
Length of sliding handle: 200 mm

Casings and doors made of 0.9 mm sheet steel, shelves can be accommodated in steps of 40 mm. Reinforced doors internally and lockable by a sliding handle with cylinder lock. Complete with 4 shelves in galvanized sheet metal.
RAL 7035 light gray body, RAL 7016 anthracite doors, powder coated.
Cylinder lock
Allowable load interior cabinet body: 500 kg
Permissible shelf load / Maximum load per rack distributed over the surface (on the metal): 80 kg
Width: 950mm
Depth: 430mm
Height: 1950 mm

Multi-component power grip. Blade of chrome vanadium steel, surface chrome-plated. Chrom-Top tips for optimum rust protection.
overall length: 82 mm
Blade length: 25 mm
for screw ⌀: 2.1 − 3 mm
Cross-head size: 1

also referenced under: ETOORASP4511, CRM 94.51

1 straight point; knurled metal handle.
overall length: 180 mm

Made of stainless steel, with return spring.
Straight jaws, plastic coated handles.
Widely applicable. Ideal for thin sheet metal, plastics, leather, cardboard, paper, cord, fabrics etc.
overall length: 140 mm
Length cutter. 30 mm

Version: Strong, forged design, special tough varnish; taper section (cutting part) bright metal. Slight internal taper for releasing the cut pieces.
Application: For punching or manufacturing gaskets and gasket rings of rubber, leather, felt, plastic, cork, fabric or similar materials.
Supplied with: 1 each steel wad punch ⌀ No. 832001: 15 pcs.
size 2-30
(2 mm increment)
Note: Use an underlay of wood, leather etc. when punching to avoid damage.

Technical Data
Packaging: Tool roll
Number of steel wad punches: 15
Type of product: Punching tool

Strong, forged design, special tough varnish; taper section (cutting part) bright metal. Slight internal taper for releasing the cut pieces.

steel

N°4, 12mm, 5000pcs

The blanks are forged and ground; manufactured with an exact cut of even density and depth using special machines. These non-convex files have tooth profiles appropriate to each grade of file.
Cuts on all faces; convex end.
The quality file for workshop use with long tool life and high removal rate.
Standard: DIN 7261 form D
Length without tang: 250 mm
Width: 10 mm

The blanks are forged and ground; manufactured with an exact cut of even density and depth using special machines. These non-convex files have tooth profiles appropriate to each grade of file.
Cuts on all faces; convex end.
The quality file for workshop use with long tool life and high removal rate.
Standard: DIN 7261 form D
Length without tang: 250 mm
Width: 10 mm

All faces and edges ground. Inspection test faces ground.
Application:
For accurate general workshop work.
Accuracy:
DIN 875 / 2 − angle tolerance e.g. for size 100×70 = 0.030mm.

Sturdy design with long arms, made of tool steel. Points and measuring faces ground and hardened. Solid spindle with adjusting nut for quick and fine adjustment. Annular spring provides constant spring tension.
With replaceable tips.

Sturdy design with long arms, made of tool steel. Points and measuring faces ground and hardened. Solid spindle with adjusting nut for quick and fine adjustment. Annular spring provides constant spring tension.
With replaceable tips.

260mm

Handy small spirit level. Die-cast aluminium profile. Face-milled measuring faces. Unbreakable acrylic vials (vertical + horizontal).
Additionally 360° rotating vial. Vee groove and magnet in the measuring face.

also referenced under: OOMAMARP3000E, CRM 94

Soft ergonomic plastic handles. Special stainless steel blades (52 - 54 HRC).
Paper, cardboard, fabric, leather, rubber, rope, etc.
Total length: 250 mm

Ergonomic soft-grip handles of plastic. Blades of non-rusting stainless steel (52 - 54 HRC).
Paper, cardboard, fabric, leather, rubber, rope, etc.
Total length: 225 mm

Ergonomic soft-grip handles of plastic. Blades of non-rusting stainless steel (52 - 54 HRC).
Paper, cardboard, fabric, leather, rubber, cord, and much more.
overall length: 200 mm

Elastic paddle in stainless steel strip, flat ovoid wooden handle.

Replacement wheel with needle bearing and quick-change axle.
Technical data
⌀ wheel 20 mm
Wheel width 6.2 mm
Roll bore 7.8 mm

Suitable for:
Wire cable cutter

for hardwood, softwood, vinyl, nylon, plaster, chalk, chipboard, linoleum, rubber, thermalite, fiberglass

Material of blade: HSS
Number of blades: 1
Blade length: 75 mm
Blade width: 3.2 mm

NIMH1434 14.4V

Sturdy metal central piece with handle of hickory, with nylon handle protection sleeve and ring wedge. The nylon inserts are impact resistant and wear-resistant, and are attached to the central piece by a double action system.
Central piece of steel.

Sturdy metal central piece with handle of hickory, with nylon handle protection sleeve and ring wedge. The nylon inserts are impact resistant and wear-resistant, and are attached to the central piece by a double action system.
Central piece of steel.

with centring jigs for conical and cylindrical cups
OOMAALIGGJ

Presentation in: Steel case
Length: 445 mm
Width: 187mm
Height: 51 mm
Number of rooms: 23
Hex key openings range: 10-34 mm
Drive profile: Hex socket wrench
Drive square: 1/2 inch

The black blade ‑ Lutz® multisharp, premium hardened blades with ultra-sharp ground edges.
Extra-fine and ultra-sharp ground blade.
Blade length: 100 mm
Blade width: 18 mm
Blade thickness: 0.5 mm
Number of snap-off points: 8
Number of blades: 10

for drilling or milling machine

Treads and stiles made of extruded aluminium sections.
Treads 85 mm deep with safe, non-slip serrated surfaces and patented 7-point tread-stile connection.
Especially light and easy to carry, with smooth stile surfaces that are comfortable to hold.
External width: 400 mm
Ladders and platforms load capacity: 150 kg
Width: 400 mm
Ladder length: 2.99 m
Working height approx.: 3.9 m
Cross beam height: 87 mm
Tread depth: 85 mm
Number of steps: 12
Material: Steps and stiles made of extruded aluminium sections

For the final finishing of prosthetic components
1 piece silicone sanding cone 5/8", conical
1 piece silicone sanding cone 5/8", conical, narrow
1 piece silicone sanding cone 5/8", cylindrical round with grooves
1 piece silicone sanding cone 5/8", cylindrical round
1 piece silicone sanding cone 5/8", double cone
1 stand

For the final finishing of prosthetic components

For the final finishing of prosthetic components