Dimensions DxH: 972 x 615mm
Necessary room height: In combination with the lamination workstations, a room height of 2.60 m is required

for: 758F200/758F220 Safety storage cabinet
Version: According to directive 2006/95/EC (Low Voltage Directive), directive 2004/108/EC (EMC Directive), directive 94/9/EC (ATEX) labelling: EX II 3/- G Ex ic nA IIB T4 Gc
Equipment: 760E14 Active carbon filter for filtering solvent vapours (hydrocarbons), filtration up to 99.99% under normal operating conditions, VDE* tested filter monitoring, VDE* tested exhaust monitoring, connection cable, mains plug *VDE: Association for Electrical, Electronic and Information Technologies
Dimensions WxDxH: 305 x 555 x 210 mm
Volume flow: 25 m /h
Material: Powder-coated thin steel sheet
Speed: 2.450 min-1
Sound intensity level: 39 dB(A)
Electrical connection in V/Hz/kW: 1 x 230 N/PE / 50-60 / 0.03
Weight: 17 kg
Colour: Light grey (RAL 7035)
To be used for: Ventilating security storage cabinets without additional exhaust ducts
Current draw: 0.13 A
Consumables: 760E14 Active carbon filter
Optional accessories: To be installed on 758F200 or 758F220 Security storage cabinet (760E13 adapter for air circulation filter needed)

The lamination bench consists of a frame with a storage surface (grid tray), a work surface for gluing work, a vacuum control box, vacuum points and clamping devices for exhaust tubes. The bench-top cabinet firmly connected to the lamination bench includes a storage surface (grid tray), a roll holder for stockinette materials, suction slots on both sides and a connection for an external fan to extract vapours.

Dimensions WxDxH: 1,750 x 650 x 750/1,750mm
Version: 3 pc. 704G11 clamping device
Diameter of exhaust nozzle for vapour extraction: 180mm
Weight: 135,1kg
Vapour extraction volume flow: Recommended 850 m³/h

Dimensions WxDxH: 1.500 x 700 x 970/1.970 mm
Volume flow: Recommended: 550 m³/h
Weight: 235,5 kg
Material: Steel/wood
Exhaust nozzle Ø: 180 mm
Scope of delivery: Connection to a vacuum system, e.g. 755E600=* vacuum system, workbench with cabinet and shelves, bench-top cabinet with roll storage and suction slots, 758Z145=10 cutting and gluing worktop with edge suction, 2 x 704G11 clamping fixture for suction pipes "Orthofix"

400V, 1.2kW, volume 40m³ / h, 25L tank

Type: VACUPRESS 620 S3 UNILOCK - COOL-TEC - Vacuum-Press for the orthopaedic
shoe technique / O&P field
Footprint: approx. . 0,34 qm / Bench-top version
Dimensions: H: 1050mm - W: 750mm - D: 590mm
Power supply: 400V / 50Hz / 3 Phase / other available
Capacity: 5,9 KW
Heating: 5400 W Infrared Quartz, reflector, 9 elements
Heating-time: Adjustable from 30-199 sec.,
2 LED Displays / Set-time + Remaining-time
Vacuum-pump 0,45 Kw 12 m³/h, two-stage - oil- and maintenance-free / motor protectionswitch
Airfilter: cartridge-type, high capacity
Frame dimensions: 450mm x 600 mm / vertical lift, working area raised on material level
Frame guide: 16 ball bearing, running in steel rails
Vacuum cavity: W: 140mm L: 190mm D: 190mm / integrated in working area,
standard
Frame locking: Main handle, located on the right hand side
UNILOCK mechanism: patented one handle material clamping system, self-adjusting from 0,5 up to 8,0 mm material thickness.
Activation grill: lateral moveable, ball bearing guided, additionally rotateable to th etop
(180°), vertical adjustable.
Illumination: 2 x 35W / 12V Halogen spotlight
Vacuum automatic: Standard - vacuum pump starts automatically when working frame is closed, shuts off when vacuum is reached Vacuum pressure is controlled during moulding process.
Heating automatic: Standard - The Infrared-Heating elements are controlled by an electronic
timer and shut off automatically when pre-set heating time is reached.
COOL-TEC Cooling System: Standard - Integrated cooling-system to decrease cooling period of vacuummoulded materials by use of special air jets. External compressed air supply required. Pressure is internally reduced to 1,5 bar.
Colour: structural effect paint, blue / light grey RAL 5017/7035

950W
560 tr/min

Oscillating plaster saw. Power : 500 W.
From 6.500 to 24.000 oscillations/minute.
Weight : 1.528 kg.
Supplied with 2 blades : Ø 50 and Ø 65 mm for natural plaster.

Light-weight and powerful 115 mm one-hand angle grinder in handy compact design, drive head can be rotated in 90° steps, quick adjustment of protective cover, M14 grinding spindle thread.
800 W motor, slim easy-grip casing, restart inhibit.
Supplied with protective hood, clamping set and additional handle.
Power consumption: 800 W
Speed range: 12,000 min-1
maximum disc ⌀: 115 mm
maximum cutting depth: 28 mm
Weight: 1.9 kg
maximum vibration to EN: 4.2 m/s2
Restart block: yes

2200 W / 230 mm angle grinder with start-up current limitation and restart inhibit.
Supplied with:
Supplied with protective hood, additional handle, clamping set.
maximum disc ⌀: 230 mm
maximum speed: 6,600 min-1
Restart block: yes
maximum vibration to EN: 8.7 m/s2
Weight: 5.2 kg
Power consumption: 2,200 W
maximum cutting depth: 68 mm
Manufacturer's designation: WS22-230E

Very compact Li-ion fast charger with practical cable reel, for 14.4 to 18 V batteries. The 4.0 Ah battery is ready for use after 25 minutes

Powerful and compact Li-Ion batteries.
No memory effect.
No loss of power.
Low self-discharge.
Fast battery charging.
Also very efficient at temperatures below 0 ° C.
Bosch CoolPack - Optimal protection of cells against overheating thanks to the special heat sink housing under the battery.

Filter surface area: 1.92 m²
Material: Felt
Thickness: 0.7 mm
Diameter: 413 mm
Length approx.: 1100 mm
Width/depth approx.: 650 mm

1.100x410mm / 0,2mm thickness

Composed of a solid core and two tough outer surfaces.
Self-healing: Exterior surfaces self-repair after cutting.

Gridlines in cm (back) and inches (front). The type designation refers to the size of the print.
Length: 870 mm
Width: 620 mm
Height: 3mm

brass

nickel plated

nickel plated

4 x 6
4 x 8
4 x 12

Material:
- EVA cork-scrap sheets

Application:
- for insoles and embeddings
- for shoe last modifications

Characteristics:
- light-weight
- thermoplastic (mouldable at approx. 130 °C)
- high density
- approx. 60 Shore A
- bonds well with contact glues

Material:
- cork-compact sheets

Application:
- for insoles and embeddings
- for height adjustments, shoe last modifications and volume adjustments of prosthetic sockets

Characteristics:
- light-weight
- bendable
- well grindable
- bonds well with contact glues

Material:
- cork-compact sheets

Application:
- for insoles and embeddings
- for height adjustments, shoe last modifications and volume adjustments of prosthetic sockets

Characteristics:
- light-weight
- bendable
- well grindable
- bonds well with contact glues

Material:
- cork-compact sheets

Application:
- for insoles and embeddings
- for height adjustments, shoe last modifications and volume adjustments of prosthetic sockets

Characteristics:
- light-weight
- bendable
- well grindable
- bonds well with contact glues

1000x1000x25mm, 15-18 Shore A

1000x1000x20mm, 15-18 Shore A

1000x1000x12mm, 15-18 Shore A

1000x1000x12mm, 15-18 Shore A

1000x1000x3mm, 15-18 Shore A

1000x1000x6mm, 15-18 Shore A

1000x1000x5mm, 15-18 Shore A

1000x1000x4mm
cell-polyethylene foam
Application:
-for padding of positioning splints and correctional braces (e.g. orthoses)
Characteristics:
-closed-celled expanded PE
-washable
-suitable for processing with Streifylen and Streifycolor
-molding temperature depending on heat source -approx.100-130 °C
-approx. 15-18 Shore A

1000x1000x3mm, 15-18 Shore A

1000x1000x3mm, 15-18 Shore A

2.5x1740x960mm

3x1740x960mm
Polyethylene foam material, thermo-moldable at approx. 110-130°C, approx. 30° Shore A

2x1740x960mm
Polyethylene foam material, thermo-moldable at approx. 110-130°C, approx. 30° Shore A

thermo-moldable at approx. 90 - 130°C., approx. 35° Shore A, 1030x1035x10mm

thermo-moldable at approx. 90 - 130°C., approx. 35° Shore A, 1030x1035x2mm

5x1100x1100mm
Polyethylene foam material, thermo-moldable at approx. 110-130°C, approx. 30° Shore A

6x1100x1100mm
Polyethylene foam material, thermo-moldable at approx. 110-130°C, approx. 30° Shore A

3x1000x1000mm
Polyethylene foam material, thermo-moldable at approx. 110-130°C, approx. 30° Shore A

6x2000x1000mm
Polypropylene copopolymer (PPC), Excellent thermoforming, Chemical and corrosion resistant, thermo-moldable at approx. 165°C, approx. 75° Shore D

Plastic acrylic resin (non-toxic), pigment dye. Clean tools with water. High hardness, low shrinkage. Protective varnish for the exterior. Practical working time 20 to 30 min. Setting time 45 to 60 min. Dosage 2 for 1, 100 g / 50 g, variable depending on the application. Consumption 200 to 300 ml per m². Realization of decorative or technical elements by molding, laminating or projection. Interior and exterior decor panel. Application in casting or in lamination with fabric + fiberglass reinforcement. Direct molding on polystyrene / bodywork. Clean use, non-toxic, durable over time, low water permeability. Supplied with: 1 Part B bottle.
Dry milk-white color.