For cervical traction - includes:
- neck harness
- transverse suspension bar
- set of washable pads

Incorporating both an adjustable angle backrest and an adjustable head/foot section with breathing hole and plug, these tables are specifically designed for lumbar and cervical traction and feature an integral rolling top design to facilitate effective traction procedures. Supplied with machine mount.
- safe working load and lifting capacity (from minimum height) of 240 kg
- integral rolling top design to provide more effective application of traction forces
- adjustable height mount for traction machine with offset positioning for changing angle of traction application
- adjustable angle backrest from horizontal to +80°
- adjustable angle head/foot section from -25° to +75° with breathing hole and plug
- the power assisted backrest and foot sections incorporate anti-trap design gas struts
- electric height elevation from 48 to 99 cm by means of a foot switch
- retractable wheel design and adjustable foot for stability on uneven surfaces
- fixation point for optional cervical traction accessory
- oilite bearings on all pivot points
- hand switch fitted as standard on electric models
- standard width 70 cm
- choice of upholstery color

The Alfatrac HT is a complete microprocessor controlled traction unit for lumbar and cervical traction. The unit can work in continuous and intermittent mode. The operator can use a large number of preset treatments and has at his disposal a memory capacity up to 50 different personalized codes.
Choice between the following modes: static, progressive, regressive, cyclic, combined.
A patient emergency stop with remote control allows the patient to stop the session. A large LCD display shows the functions. An acoustic signal indicates the end of traction. Without accessories.

Technical Features:
- OS: Windows CE
- mains: 110-230V - 50/60 Hz
- consumed power: 80 VA
- maximum measurement range: cervical treatment 25 kg, lumbar treatment 90 kg
- treatment time: 1 - 60 min
- dimensions: 41 x 42 x 18 cm
- weight: 12 kg

Contains:

Chest Strap
Set of Counter-Traction Straps
Pelvic Strap
Chin Strap
Spreader Bar
Round Pillow
Leg Rest Height Adjustable by Cylinder

The tapered Torx® HF profile reliably retains all Torx® screws. L-shank; through hardened (hard and tough).
Ideal for starting and tightening Torx® screws where access is difficult.
Material: Chrome vanadium steel, manganese phosphated.
Supplied with table use:
1 each L-wrench in a plastic clip: TX8; TX9; TX10; TX15; TX20; TX25; TX27; TX30; TX40

Clés dynamométriques à un bras sans vernier de réglage. Réglables par un appareil de contrôle de clé dynamométrique

Kraftform handle for easy transmission of the required torque. With Rapidaptor quick-change holder for 1/4 inch bits with C6.3 and E6.3 shank. Sizes 600 and 880 with pistol grip for transmission of higher torques.
The torque can be set using a torque analyser (No. 654300 − 654460) and a 7AF hexagon screwdriver (10AF for size 600) . The torque screwdrivers are factory-set to the most frequently used torque setting.
When the set torque is reached the screwdriver triggers, with clearly audible and perceptible signals. The triggering torque is unrestricted.
maximum torque: 120 cN·m
set torque: 0.3 N·m
Bit socket: D6.3 ; F6.3
Torque range:0.3 N·m - 1.2 N·m
Connection format: bitholder 1/4 tomme
Overall length L: 155 mm
Adjustable trigger value: pre-set

139 tools

BRAND: ORTHOPUS
Material: stainless steel
Dimensions: Ø53
Weight: 40.8g
Thread: M10
Made in France
It allows you to use all kinds of tools for everyday life by quickly attaching them to the universal wrist (REF 80 P 20.W).

- protects and separates tools during transport
Specifications: padded, adjustable partitions, handle
External dimensions: 48 x 34.5 x 19.5 cm
Weight: 1.35kg

also referenced under: OOMAOVENCR50K, CRM 40

120 minutes

also referenced under: OOMAOVENCR50I, CRM 29

This vise tilts 90 degrees and is solidly constructed. Thanks to its excellent clamping force, the vice does not move when drilling or milling.
Made of cast iron, the vise is strong and sturdy. This vise has an adjustable tilt angle between 0 and 90 degrees, and a locking pin on the chain to secure it every 15 degrees.
This unit also features a stable base, which can be easily mounted on your workbench. It is compact and lightweight, making it suitable for mobile use.

Specifications
Material: cast iron
Jaw width: 105mm
Jaw opening: 110 mm
Jaw depth: 47mm
Base size: 190 x 185 mm (L x W)
Tilt adjustment: 0 - 90 degrees
Height: 120mm (lying), 220mm (standing)

STANDARD AND ECONOMY VERTICALIZATION TABLES CHARACTERISTICS:
lifting force of 225 kg, therefore suitable for heavy patients
height and righting by electric motor with manual control
large wheels and centrally controlled brakes on the Standard model, wheels with individual brakes on the Economy model
the double foot support can be individually tilted from + 15 ° to -30 °
supplied with retractable handles and set of fixing straps depending on the model
Adjustable work table on the Standard model (option for Economy model)
goniometer for reading the inclination
90 ° full standing position
minimum height 47 cm and maximum 101 cm
base accessible to patient lifts
self-lubricating moving parts ensure quiet operation
standard width: 70 cm
cover available in various colors

• Fixed height 49 cm to allow for easy transfer of wheelchair patients
• The design of the support frame allows smooth lifting and transfer of the patient
• Electric motor with a thrust force of 6000 N for positive tilt option
• Positive tilt up to + 88˚
• Folding and adjustable footboard + - 15˚
• Equipped with set of 3 fixation belts
• Two fixed and two swivelling castors all with blocking mechanism
• Manual control switch
• Fire-retardant padding and covering class 1IM
• Patient transfer access 14 cm
• Max. load for the entire table: 120 kg
• Dimensions: 200 x 65 x 49h cm

The blanks are forged and ground; manufactured with an exact cut of even density and depth using special machines. These non-convex files have tooth profiles appropriate to each grade of file.
Cuts on all faces; convex end.
The quality file for workshop use with long tool life and high removal rate.
Standard: DIN 7261 form C
Length without tang: 250 mm
Width: 18 mm

also referenced under: OOMAMARP3000F, CRM 95

These sealants replace hemp, sealing tapes, and pastes, they are resistant to gases, liquids, air, water, oils, hydrocarbons and many chemical products. Complete surface contact ensures a 100% seal. Unscrewing, or correction of position during assembly can be performed using conventional tools at any time before the sealant hardens. No sealant residues to block filters and valves.
The stick with pasty sealant is economical in consumption, no drips after use.
Application:
Improved bonding of suckers.
Note:
Before applying sealant, clean the threads with general-purpose cleaner
Labelling of hazardous substances: GHS07 Caution
Content of stick: 19 g
Colour of sealant: orange
minimum break-away torque: 5.8 N·m
Temperature range: -55 °C - 150 °C
for thread size M to: M80
for imperial thread size: 3 inch
Strength for disassembly: low
fluorescent:no

also referred as: OOMAOPRECR75T, CRM 76

FUNCTION: Programmer, Controller
DIMENSIONS: 48 x 48 mm
DISPLAY: 1 display with 4 digit
POWER SUPPLY: 24 Vac/Vdc, 100… 240 Vac
INPUTS: 0/1… 5 V, 0/2… 10 V, 0/4… 20 mA, Pt100, PTC-NTC, Thermocouple
OUTPUTS: Relay and/or SSR control
DIGITAL INPUTS: 1, 2
INDEPENDENT TIMER: Yes
NUMBER OF PROGRAMS / SEGMENTS: 1 program with 8 segments
INTERFACE: TTL Modbus
SPECIAL FUNCTIONS: Digital retransmission, Hours/Days worked, Power on delay, Soft start, Transmitter power supply, User calibration, Wattmeter
CONTROL: ON/OFF and PID single or double action
EXTRACTABILITY: By the front
CERTIFICATIONS: CE, UL

Specially parameterized for CR5000G

also referenced under: OOMAOVENCR50RG, CRM 46, K48

also referenced under: OOMAOVENTHERDIG, CRM 53

also referenced under: OOMAOVENTERMO, CRM 47

50 cm

Its texture allows it to breathe and to drain perspiration.
Very comfortable and soft to the touch
Easy to clean, washable at 40°C / 100°F.
Good ageing
Glue-less, this fabric complies with sustainable development policies and limits risks of allergy
Thermoformable at 170°C / 340°F.

Its texture allows it to breathe and to drain perspiration.
Very comfortable and soft to the touch
Easy to clean, washable at 40°C / 100°F.
Good ageing
Glue-less, this fabric complies with sustainable development policies and limits risks of allergy
Thermoformable at 170°C / 340°F.

400x400x15mm
Suitable for fabricating flexible inner prosthetic sockets,
especially in lower limb prosthetics
Product information:
• Ethylene vinyl acetate
• Also in antibacterial (616T253)
• High flexibility
• High surface quality
• Can be subsequently thermoformed
• Minor shrinkage: approx. 3%
• Comfortable to wear
• Washable
• Temperature recommendation: 160 °C/320 °F
(convection oven, infrared oven)

long shape that protects hands and wrists
tight-fitting for good dexterity when shaping sockets
one size (size 9), with Para-Aramid, seamless

ENP 220, spare part

also referenced under: OOMAOVENCR50FT, CRM 28

ENP 360°, spare part

The new TRC HT is an innovative device for performing Therapeutic Resistive Capacitive Diathermy.
TRC is the new and more effective approach in diathermy for all the professional operators who are looking for something more than a traditional diathermy unit (microwaves or shortwaves).
TRC is more selective than shortwave and microwave.
Resistive Diathermy generates a deep action over bone, ligaments, tendons and muscles. It could also be used for drainage and relaxing contractions. Heat effect is generally quite important.
Capacitive Diathermy produces biological stimulation, particularly over the treated area just where the electrode has been placed. It’s athermal or a comfortable minimal heat effect.
Further to the main massage application, Resistive and Capacitive Diathermy can be also performed by placing a static applicator over the area to be treated.
All the functions are visualized on a large color LCD. In addition to the usual and traditional keys and buttons, it is possible to adjust every parameter on the touchscreen.
The versatile Windows CE operating system ensures possible upgrading.
A wide range of preset protocols with body maps is available. After a pathology is chosen, the screen will show the body parts to be treated and the unit will suggest the parameter values to set.
Free memories for entering customized protocols.
Technical Features
- frequency: 485 kHz ± 10 Hz
- emission: continuous and pulsed
- power: adjustable from 20 to 180 W
- impedance: in real time
- temperature sensor
- color touchscreen 400 x 800 pixels
- power supply: 115-230 V~ 50/60 Hz
- consumed power: 750 VA
- dimensions: 40 x 30 x 23 cm
- safety class: class I type BF according to IEC 601-1
- Directive EEC 93/42: IIb

• Safe working load and lifting capacity of 240Kg (528lbs)
• The power assisted backrest section incorporates anti-trap
design gas strut
• Backrest angle adjustment from -25˚ to +75˚
• Choice of hydraulic or electric height elevation
• Excellent height range from 45cm to 98cm
• Retractable wheel design with adjustable foot for stability
on uneven surfaces
• Breathing hole and plug included as standard
• Purpose made precision bearings on all pivot points
• Clearance beneath frame for mobile hoist
• Hand switch fitted as standard on electric models
• Standard upholstery width of 65cm

Clipper VI with an adjustable frame and armrests for extra strong support. Steel frame and aluminium legs covered with epoxy painting.
It is height adjustable to reach the best comfort and safety.
Materials: polypropylene, epoxy coated steel and aluminium
• 4 clips for a safe fixation
• Epoxy coated steel armrests with soft padding
• 100% sturdy polypropylene structure
• Exclusive design
• Front cutout for personal cleaning
• Tool free installation
• Easy to remove for cleaning
• Easily fits to most toilets
• Raises by 11cm (4.3 inches)
• Tested for 150kg
Height: 52/65cm
Max. body weight: 150kg

The Clauss 7” PowerFleXX Shears feature stalwart, Titanium Bonded blades that are 3x harder than untreated stainless steel and provide exceptional edge retention across countless cuts. The handles are just as strong, offering impact and shock resistance along with oversized bow design for increased comfort and reduced hand fatigue. Also featuring multi-directional ground blades, fully adjustable tension, and knife edges for superior cutting performance, the PowerFleXX Shears are a strong option for those seeking well-rounded and long-lasting shears.

Titanium bonded blades are 3x harder than untreated stainless steel and will stay sharp for longer
Impact/shock resistant handles
Oversized bows
Multi-directional ground blades
Knife edges for superior cutting performance
Fully adjustable
Lifetime Warranty

• 10 different height adjustments 75 cm Δ 104 cm

high-quality masking tape for painters, plasterers and bodywork painters, up to 80°C, well-impregnated reinforcement or very good resistance to re-sanding, also ideal for dispersion paints

also referenced under: OOMAOVENCR50O, CRM 43